110V 220V AC Digital LED Temperature Controller XH-W3001 Cooling Heating Switch NTC Sensor Thermostat

W3001 microcomputer controller instruction

Item Type: Digital Temperature Controller

Model: XH-W3001

Output Type: Direct Output

Output power: 10A Max.

Power Supply 🙁 12B; 24b; DC),(220 V; AC)

Load Power: 120 W; 240 W; 1500 W;

Temperature measurement range: -50 °C ~ 110 °C

Temperature control range: -50 °C ~ 110 °C

Temperature control accuracy: 0,1 °-0,2 ° C

Input measurement: Waterproof probe ntc10k L = 1 meter waterproof

How to install

1. Press the up button to show the initial temperature.

2. Press and hold the up button until the temperature display starts to flash. Click up or down.

3. Set the initial temperature value.

4. Press the “Down” button to show the stop temperature.

5. Press and hold the “down” button until the temperature display starts to flash, press the “up” or “down” button.

6. The Button set the stop temperature value.

Connection instruction:

Way to connect 12 V/24 V

Advice:12 V/24 V W3001 power supply, you can use transformer or 12 V/24 V DC power supply

Note:W3001 is a direct output, so when the output is not connected to the load, do not turn on the power to prevent two-level contact between the wires and the ignition.

220 V connection method:

What is direct inference?

Reminder:The output and input voltage of this thermostat are synchronized, that is, when the thermostat is operational (the indicator light is on), the input voltage is a direct output voltage. When the thermostat works intermittently (the indicator is not lit), there will be no output voltage on the output terminal.

The indicator light is on, indicating that there is an output on the output terminal.

The indicator is not lit, showing that there is no output at the output terminal.

Usage instructions:

Set start temperature:

Press the “up” button once to display the start temperature, press and hold the “up” button for about 3 seconds, the number of start temperature will flash, and the desired temperature value can be set with the up and down buttons.

Set stop temperature:

Press the “down” button once to display the stop temperature, press and hold the button for about 3 seconds, the stop temperature number will flash, and the desired temperature value can be set with the up and down buttons.

How to restore factory settings?

Press and hold the up and down buttons at the same time when power is on, the digital tube displays the 888, and then automatically goes to the detection temperature, that is, restore the factory settings.

Heating setting instructions

Basic setting parameters: initial temperature <final temperature (the program automatically determines that the working mode is the heating mode)

How to install:

1 Press and hold the “up” button, the start temperature will flash, and set the start temperature value with the “up” and “down” buttons.

2. Press and hold the adjustment button to stop the temperature flashing, and use the up and down Keys to set the stop temperature value.

Use scenarios:

Control the water heater, stop the heating when it reaches 65 ° C, and turn on the heating again when the temperature drops to 50 ° C. How to customize?

Step 1: Determan the working mode as the heating mode, the initial temperature <final temperature.

Step 2: Press and hold the “up” button, the start temperature will flash, and set the start temperature to 50 °C by pressing the “up” and “down” buttons.

Step 3: Press and hold the adjustment button to stop the temperature flashing, and set the stop temperature to 65 ° C with the up and down buttons, and the setting is complete!

Cooling mode setting instructions

Basic setting parameters: initial temperature> final temperature (the program automatically determines that the operating mode is the cooling mode)

How to install:

1 Press and hold the “up” button, the start temperature will flash, and set the start temperature value with the “up” and “down” buttons.

2. Press and hold the adjustment button to stop the temperature flashing, and use the up and down Keys to set the stop temperature value.

Use scenarios:

Control the truss, stop ventilation at 26 °C and start cooling again when the temperature rises to 28 °C. How to set it up?

Step 1: Make sure the working mode is cooling mode, initial temperature> final temperature.

Step 2: Press and hold the “up” button, the start temperature will flash, and set the start temperature to 28 °C with the “up” and “down” buttons.

Step 3: Press and hold the adjustment button to stop the temperature flashing, and set the stop temperature to 26 ° C with the up and down buttons, the setting is complete!

Installation introduction:

W3001 is made of 1,8mm ABS plastic. Both sides have side holes for easy installation and fixing.

Application Area:

W3001 uses a single chip microcomputer control system and high-precision temperature control sensor with outstanding temperature control characteristics and accuracy. Simple control panel, wide temperature control range, independent evaluation of heating and cooling mode, easy adjustment. ABS composite material with a thickness of 1,8mm is not only beautiful, but also reliable in quality and does not age. I cut holes as shown in the picture, which can be directly installed or embedded in the panels of industrial control equipment, etc. D. It is convenient and fast, and widely used in the fields of incubation, chassis equipment, air conditioning systems, temperature control.