Flexible Solar Panel 100W,200W 12V Solar Panel Kit Monocrystalline module, controller cable for outdoor off grid battery charger

BOGUANG Flexible Solar Panel 100W,200W 12V Solar Panel Kit Monocrystalline module,10A /20A charge controller, extension cable,Alligator clip cable for outdoor off grid boat rv trailer (100W OR 200W Solar Panel kit)

About this item

*High Efficiency: solar panels use new Perc solar monocrystalline cells, up to 23% conversion rate, 100w solar panels are smaller, lighter and more portable
*Semi-Flexible: The plastic back sheet can be curved to a maximum 30 degree arc and mounted on RV, boat, cabin, tent, car, trucks, trailers or any other irregular surface.
*Thin & Lightweight：100W solar panel weighs approximately 4lb,Thickness is 0.1in， weighs 70% less than conventional solar panels, making transportation and installation a breeze.
*Practicality: Light energy converts electricity, Practical and suitable for use in areas where electricity is not available and where the city cannot reach, such as mountains, marine, deserts, and remote areas
*Nice Details: The component contains a bypass diode, and the circuit uses input over current protection and reverse protection design.The solar panel has 6 grommet mounting holes are available to attach fasteners，and can also be installed with silicone and adhesive tape.

Package 1:12V 100W Solar Kit

1. 1 pcs 19.8V 100 Watt solar panel

2. 10A 12v/24v charge controller

3. 1 set 3m Extension cable with PV connector

4. 1 set 1.5m cable with alligator clip （connect to battery）

OR

Package 2: 200W Solar Kit

1. 2 pcs 19.8V 100 Watt solar panel

2. 20A 12v/24v charge controller

3. 1 set 3m Extension cable with PV connector

4. 1 set 1.5m cable with alligator clip （connect to battery）

5. 2 in 1 adaptors

100W Solar Panel Specification

Maximum power(Pmax) ：100W

Open circuit voltage(Voc) ：21.6V

Short circuit current(Isc)：6.11 A

Maximum power voltage(Vmp)： 18V

Maximum power current(Imp)：5.55A

Temperature range： -40℃～+80℃

Maximum system voltage ：700V DC

Weight ：1.85kg(4 lb)

Size：41.73×20.86×0.11 in(1060x530x3mm)

Standard Test Conditions ： lrradiance 1000w/m2，Temperature 25℃,AM=1.5

The Boguang 100Watt flexible solar panel is made of PERC Monocrystalline cell with a conversion rate of 23%. The weight is 1.85kg（4lb）, which is 20% of the traditional solar panels.Size is 41.73×20.86×0.11 in(1060x530x3mm). The lightweight nature of flexible solar panels makes solar panels more effective for use in RVs, caravan，boats, tents, trailers, cabin, etc. Portable, easy to install, plug and play.

[Excellent performance] High efficiency monocrystalline solar cells offer good performance even under poor light condition,Including bypass diode, circuit with input overcurrent protection, reverse protection design

[Flexible] This flexible solar panel is a good choice for curved surfaces of RV, boat,sailboat, yacht,truck, car, coach, cabin, camper , tent , trailer, golf cart or any other irregular surface.

[Practicality] Light energy converts electricity, Practical and suitable for use in areas where electricity is not available and where the city cannot reach, such as mountains, marine, deserts, and remote areas.

[Lightweight] Ultralight and Ultra-thin ,Better applied to the carrier with weaker bearing, attached to the surface, no space,easy to install,

[Nice Details] The water resistant semi-flexible solar panel is far more durable than traditional glass and aluminum models, The junction box is sealed and waterproof.

24V Solar panel kit connection diagram

12V Solar panel kit connection diagram

Solar system kit wiring method and precautions

1.The solar system kit connection is divided into parallel connection or serial connection. The controller must be first connect the battery , and then connect the solar panels.

2.When the solar panels are connected in series or in parallel, paid to the highest PV input voltage of the controller. The voltage connected in parallel to the controller after the series connection cannot exceed the maximum input voltage of the controller.

3.The total input power of the solar panel can't be greater than the rated power of the controller, otherwise, there is a risk of burning the controller.

4.When the cable is connected to each component, the connection should be stable and there should be no looseness.

5.The positive and negative poles of the controller and battery should be checked clearly. Do not reverse the positive and negative poles.

6.When the power rating of one controller is insufficient to meet all solar panels, multiple controllers can be simultaneously connected to the battery.