product description:
This remote control infrared alarm is a set of infrared detector and alarm in one, with wireless remote control and power supply to form an alarm system. Once the infrared detector detects an illegal human movement intrusion, it immediately activates a high-decibel siren to emit a 30-second on-site alarm sound, which plays a powerful deterrent role. The alarm uses a special infrared sensor processing chip, PIR dual element pyroelectric infrared sensor, Fresnel lens and advanced digital remote sensing technology, micro power consumption special integrated circuit and automatic temperature compensation technology, using microprocessor decoding control, etc. Advanced integrated design technology. By detecting the infrared thermal energy radiated by the human body, the on-site audible alarm of the probe is activated to prevent theft in time. It is an ideal anti-theft facility for various vehicles, homes, shopping malls, offices, courtyards and storefronts along the street. It is an indispensable anti-theft product for modern families, shops, enterprises and institutions, and business stays in hotels.
Features:
1. Infrared detection
2. Long-distance multi-channel wireless remote control, originally equipped with two remote controls, the same principle as the TV remote control.
Technical Parameters:
Alarm sound level: 105dB (decibels)
Remote control distance: about 5-10 meters (open area)
Detection range: detection distance of about 7 meters
Working voltage: AC 220V (requires self-equipped transformer), DC 6V (4 batteries can be installed in the 5th, need to bring their own) using a dedicated module consumes very little power
Installation requirements:
◆The remote infrared warning device should be able to look directly at the protected area without obstacles.
◆When installing, avoid infrared warning devices close to hot and cold sources, such as hot and cold air outlets, air conditioner air outlets, electric heaters, coolers, etc., and avoid direct door.
◆The remote infrared alarm should be at an angle of 10 to 30 degrees with the wall. At this time, the detection distance is the farthest. Adjust the installation angle according to the situation during actual installation.
◆Because the remote infrared warning device has the highest infrared detection sensitivity when the human body moves laterally with respect to the lens, but the longitudinal motion sensitivity is poor, so the angle and height of the horizontal plane of the detector should be paid attention to during installation, which has a great impact on the protective area.
Brief introduction:
After the installation is set, the switch is turned on, the owner can leave the sensing area within the time of delayed work, the electronic dog enters the working state in about 15 seconds, and someone passing the sensing area will emit an alarm sound, and it is necessary to avoid the sensing range when shutting down. No sound will be produced when it is turned off. Sensing range: horizontal angle is 110 degrees and vertical angle is 35 degrees. It is a fan-shaped area. Just like the video of the camera, there is a visible range. If it is not in the sensing range, it will not be called when someone moves. , Normally around 7 meters, the sensing distance and sensing area range can be adjusted according to your needs. When you press the remote control button during use, the host beeps once, indicating that you are in the armed state. After a delay of about 10 seconds, if someone is detected in the armed area, you will immediately alarm for 30 seconds at high loudness. After pressing the remote control button, the host will beep once. , Means entering the state of disarming, allowing personnel to move in the fortified area. During the alarm, as long as the remote control button is pressed at will within the effective distance, the alarm can be stopped immediately.
Instructions:
1. Turn on the power switch, the power-on indicator lights up once, indicating that the self-test is normal.
2. The remote control infrared warning device has a standby delay of 10 seconds immediately after it is turned on, and does not detect the alarm signal within 10 seconds. You must leave the detection area of the electronic dog within these 10 seconds.
3. If someone enters the detection area of the infrared siren after 10 seconds, the remote infrared siren will have a delay of 5 seconds, which facilitates the identification of the owner. After 5 seconds, if there is no signal to identify the remote control, it will The alarm sounds for 30 seconds, the alarm volume is 105 DB. 5 seconds after the end of the alarm sound, if another person touches the remote infrared alarm, it will alarm again and again and again.
4. You can use the remote control to turn off the power switch to stop the alarm when the remote infrared alarm is on the alarm.
Installation guide:
1. The probe should avoid directly facing the door window to avoid false alarms
2. The tilt angle of the detector should be adjusted so that the detection distance is the farthest
3. The probe’s Finiell lens should be kept clean and free of obstructed objects
4. The probe should be far away from cold and heat sources, such as air conditioner outlet, heating, air conditioner, etc.
5. Enter the alert state within 10 seconds of starting up, and detect someone alarming for 30-50 seconds
6. Open the battery cover and insert 4 batteries of size 5 according to the logo inside the battery box
7. When installing and using, avoid direct sunlight, car lights and probes, and consider the false alarm caused by the floating curtains
8. Installed on the corner of the wall or on the wall. It is recommended that the installation height be 2 meters above the ground. Adjust the view angle to prevent false alarms of small animals
9. Fix the remote infrared alarm on the universal seat, and turn the infrared alarm to meet the installation requirements and detection needs.
Precautions:
●When the remote control distance is shortened, replace the battery.
●When the battery is installed in the detector, regularly check whether the battery leaks.
●It is recommended that you regularly check whether the infrared alarm is working properly to avoid missing alarms.
●The detector should be protected from rain, wind, and sunlight. Indoor heat sources such as air conditioners and stoves should be avoided to avoid false alarms.
●When the power-on indicator is dark when the power is turned on, the alarm sound becomes smaller, and the false alarm rate of the infrared alarm is higher, the battery voltage is generally insufficient, and the battery should be replaced in time.
The packaging includes:
2*remote control
1*Alarm
Thank you for your support!Welcome to buy from us!You can contact with us to get more detail of the goods .Have a nice day!
