long arm actuator PKM-C022 Heavy-Duty Solar Single Automatic Gate Opener Kit for Swing Gates Up to 20 Feet (ft.)

long arm actuator PKM-C022 Heavy-Duty Solar Single Automatic Gate Opener Kit for Swing Gates Up to 20 Feet (ft.)

Produrct feacture：

1.Easy to install and operate,and easy to connect wired.
2.Open and close the gate by remote control and keypad.
3.Time promotation function.when open gate,speed is slow,then a little quick,and when close the door,speed is slow again.
4.In case of power failure,release the clutch easily,and can operate the gate manually.
5.Stop working when gate meets with obstacle.
6.Rod's max travel is 500mm.
7.Motor's Poweer : 24VDC 60W
8.Running Speed :1.6cm/s
9.Run travel : 500mm
10. Max single leaf gate width: 6M(max)
11.Max single leaf gate weight: 400KG
12.open to inside or outside all ok.

Standad kit components:

①1* Arms Gate Openers(drive motor)
②1* Control Box(with transformer)
③1* A set of Hardware Accessories
④1*Rubber stopper
⑤2* Remote Control
⑥1* Manual English

Other additional accessories are optional
choose color kit,accessories show the picture

Control Box details

Support for solar systems(Optional accessories)

Can be plugged into a solar system, using a home circuit, or solar powered. Note that we cannot transport the batteries and need to prepare the batteries yourself.

SWING GATE OPERATOR

Digital LED Menu brings a easy setting ,plug and play
Availble to set pedestrian mode
Adjustable working time
Adjustable resistance sensitiv
Adjust auto-closing time
Terminal availble for loop detector ,photocell,push button, keypad , access control equipment etc.
Custom rolling code makes the system more secure, high anti-theft performance

1. 2 SIDE terminal is used for connecting any external device that operates double gate
2. COM terminal is COMMON used for connecting the “ground” of external devices
3. 1 SIDE terminal is used for connecting any external device that operates single gate
4. Swipe Card terminal is used for connecting any external devices that will operate to open the gate
5. COM terminal is COMMON used for connecting the “ground” of external devices
6. Infrared terminal is used for connecting photo electric sensor
7. 12V DC output is used for connecting photo electric sensor (Continuous output current <=200mA)
8. 24V battery output is used for connecting the back up battery +
9. 24V battery output is used for connecting the back up battery –
10. 24V DC output is used for connecting external device. (such as photo electric sensor, max current output 1A)
11. GND is used for connecting the “ground” of external devices
12. 24V DC lamp output is used for connecting flash light +.
13. 24V DC lamp output is used for connecting flash light -.
14. 24V DC lock output—the NF terminal which used for connecting the electric lock
15. COM is COMMON used for connecting the “ground” of lock
16. 24V DC lock output—the NA terminal which used for connecting the magnetic lock
17. 24V DC alarm output
18. 24V DC alarm output
19. and 20. Motor1 terminal is used for connecting the motor 1 installed on the gate that opens later and close first. This terminal connect 1st red wire (counted from your left hand side to right hand side)
21. and 22. Motor2 Delay terminal is used for connecting the motor 2 installed on the gate that opens first and close later. This terminal connect 1st blue wire (counted from your left hand side to right hand side). NOTE! If for single gate, the gate motor just can connect the Motor2 Delay terminal.
23. AC24V input is used for connecting the transformer
24. AC24V input is used for connecting the transformer
25. digital display is used for showing you the setting data
26. INC+ is used for figure increase when setting the data
27. FUN is used for store the data
28. DEC- is used for figure decrease when setting the data
29. Learning button is used for program/remove remote
Need more clear instructions and installation tutorial Please contact the seller to use
e-mail send
E-Mail:kingjoin81@sina.com

Installation details