Wifi RF 433 Mhz DIY Light Switch Module Receiver Relay 86 Portable Wireless Remote Control Tuya Smart Life Alexa Google Home

Wenzhi Wieless Wifi + RF433 Mhz receiver & RF 433 Remote Control

Receiver Parameter

Input Voltage : AC 90-250V
Max Current : 10A
Maximum load power:
resistive power 2200W
Induction power 500W
Capacitive power 200W
Incandescent lamp 2200W
LED light 300W
Energy-saving lamp 300W
The number of lights that can be controlled at the same time: less than 6 lights, and thelight strip is less than 6 meters
Operating Frequency: 433MHz
Wifi: 802.11 b/g/n
App: Tuya / Smart Life
Dimensions: 82mm*42mm

Remote Control

Battery Model: CR2032 (Package Not included battery)
Dimensions: 88mm x 90mm x 10mm
Distance: 20-30 meters

Notice: The package Included different products because you choose a Different options.

NOTE
1) Do not wire with power on, turn off the power to wire, and power on after checking and confirming that it is correct.
2) When the remote control voltage is low, please replace the battery in time (when the remote control battery voltage is low, the remote control distance will generally become shorter).
3) When using wireless electronic products, pay attention to avoiding metal masks, large electronic devices,electromagnetic fields and other strong sources of interference, so as to avoid the short distance between the remote
control and the receiver or the failure of normal operation.
4) Do not use this electronic product abnormally. Abnormal use will reduce the performance and life of the product. In severe cases, it will damage the product and bring hidden dangers to your safety.

How to install this smart switch

You don't need to open the outer casing of this smart switch
You can wire directly to the terminal block

Please note: Please turn off the power before wiring.
Please connect the wires according to the following diagram

After the wiring is completed, turn on the power and operate according to the status of the smart switch indicator:
1) If the LED light of the smart switch flashes continuously at this time, it indicates that the smart switch has entered the state of waiting for connection to WiFi; then open the APP and follow the instructions to connect to WiFi.
2) If the indicator light of the smart switch is not flashing LED light, please press the button of the smart switch and keep it for more than 5 seconds until the LED light flashes continuously, then open the APP and connect to the WiFi according to the manual.

How to match smart switch with 433Mhz RF remote control?

This smart switch has 3 working modes to match the 433Mhz RF remote:
(smart switch, hereinafter referred to as: receiver)

1. Momentary mode: Press the Remote control button, the receiver's relay is ON; release button, the receiver's relay is OFF.
2. Toggle mode: Press Remote control button for 1 time, the receiver's relay is ON; press button again, the receiver's relay is OFF.
3. Latched mode: Press Remote control button A, the receiver's relay is ON, Press the transmitter's button B, the receiver's relay is OFF.

Reset function: After push the receiver's learning button 8 times, the receiver Clear all the remote control data in its memory.
When the LED flashes for a few times, it indicates that the clear function is completed.
(After cleared the code in the receiver, all the remote control cannot work with the receiver.)

Matching method:

1. Setting momentary Mode:
Press the receiver's Learning button 1 time, the receiver's red LED will be lights up, it comes into Setting state; Press the remote's button, the receiver's red LED will flash then come off, Setting successfully.
2. Setting Toggle Mode:
Press the receiver's Learning button 2 time, the receiver's red LED will be lights up, it comes into Setting state; Press the remote's button, the receiver's red LED will flash then come off, Setting successfully.
3. Setting Latched Mode:
(Note: When you choose “Latched Mode”, you need to setting two different buttons on the Remote control, the first time learn is for “ON”, the second time learn for “OFF”.
For example: button A = ON, button B = OFF)
Press the receiver's Learning button 3 time, the receiver's red LED will be lights up, it comes into Setting state; Press the remote's A button, the receiver's red LED will flash and then remains lit; Then press the remote's B button, the receiver's red LED will flash then come off, Setting successfully.
Note: A Smart Switch can only store 12 buttons (on the remote). Saved button number of more than 12, it will cause all of the stored remote control cannot control the Smart Switch. You need reboot the power and reset the RF remote control settings (press the Smart Switch's matching button 8 times)